Thông tin chi tiết sản phẩm:
Thanh toán:
|
Data Links: | 11.3Gbps | Distance: | 40km |
---|---|---|---|
EML transmitter: | Support | PIN receiver: | Support |
SFP+ MSA with LC connector: | Support | Hot-pluggable SFP+ footprint: | Support |
Điểm nổi bật: | cisco compatible sfp modules,fiber optic transceiver module |
10G SFP+ 1550nm 40km Single Mode SFP Optical Transceiver Module
LNK-10G-SFP-L45: 1.4W power dissipation without CDR for Industrial temperature LNK-10G-SFP-L45C: 1.5W power dissipation with CDR for Industrial temperature
STANDARD
Ordering information
Product part Number |
Media |
Wavelength (nm) |
Transmission Distance(km) |
Temperature Range (Tcase) (℃) |
With/Without CDR |
LNK-10G-SFP-L45 | Single-mode fiber | 1550 | 40 | -40~85 | Without CDR |
LNK-10G-SFP-L45C | Single-mode fiber | 1550 | 40 | -40~85 | With CDR |
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Storage Temperature | Ts | -40 | - | 85 | ºC | |
Relative Humidity | RH | 5 | - | 95 | % | |
Power Supply Voltage | VCC | -0.3 | - | 4 | V | |
Signal Input Voltage | Vcc-0.3 | - | Vcc+0.3 | V |
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Case Operating Temperature |
Top |
0 | - | 70 |
ºC |
|
-40 | 85 | LNK-SFP-10G-L45 | ||||
Power Supply Voltage | VCC | 3.14 | 3.3 | 3.47 | V | |
Data Rate | BR | 10.3125 | 11.3 | Gbps | ||
Max transmission Distance | TD | 40 | km | |||
Coupled fiber | Single mode fiber | 9/125um SMF |
Parameter | Symbol | Min. | Typ. | Max. | Unit | Note |
Transmitter | ||||||
Average Launched Power | PO | -1 | +3 | dBm | Note (1) | |
Extinction Ratio | ER | 8.2 | dB | |||
Center Wavelength | λc | 1530 | 1550 | 1565 | nm | |
Spectrum Band Width (-20dB) | σ | 1.0 | nm | |||
SMSR | 30 | dB | ||||
Transmitter OFF Output Power | POff | -30 | dBm | |||
Transmitter and Dispersion Penalty | TDP | 2.0 | dB | |||
Output Eye Mask | Compliant with IEEE 802.3ae | |||||
Receiver | ||||||
Input Optical Wavelength | λ | 1270 | 1610 | nm | ||
Receiver Sensitivity | Psen | -16.0 | dBm | Note (2) | ||
Input Saturation Power (Overload) | Psat | 0 | dBm | |||
LOS Assert | LOSA | -30 | dBm | |||
LOS De-assert | LOSD | -17 | dBm |
LOS Detect Hysteresis | Phys | 0.5 | dB |
Note:
Parameter | Symbol | Min | Typ | Max | Unit | NOTE |
Supply Voltage | Vcc | 3.14 | 3.3 | 3.46 | V | |
Supply Current (Note 1) |
Icc |
370 |
mA |
|||
430 | LNK-SFP-10G-L45 | |||||
400 | ||||||
460 | LNK-SFP-10G-L45C | |||||
Transmitter | ||||||
Input differential impedance | Rin | 100 | Ω | 2 | ||
Single ended data input swing | Vin-pp | 180 | 700 | mV | ||
Transmit Disable Voltage | VDis | 2.0 | Vcc | V | 3 | |
Transmit Enable Voltage | VEN | Vee | Vee+ 0.8 | V | ||
Transmit Disable Assert Time | 10 | us | ||||
Receiver | ||||||
Differential data output swing | Vout-pp | 400 | 800 | mV | 4 | |
Data output rise time | tr | 28 | ps | 5 | ||
Data output fall time | tf | 28 | ps | 5 | ||
LOS output high level | VLOS-H | 2.0 | VCCHOST | V | 6 | |
LOS output low level | VLOS-L | Vee | Vee+0.8 | V | 6 | |
Power Supply Rejection | PSR | 100 | mVpp | 7 |
Pin out of Connector Block on Host Board
Pin | Symbol | Name/Description | NOTE |
1 |
V EET |
Transmitter Ground (Common with Receiver Ground) | 1 |
2 |
T FAULT |
Transmitter Fault. | 2 |
3 |
T DIS |
Transmitter Disable. Laser output disabled on high or open. | 3 |
4 | SDA | 2-wire Serial Interface Data Line | 4 |
5 | SCL | 2-wire Serial Interface Clock Line | 4 |
6 | MOD_ABS | Module Absent. Grounded within the module | 4 |
7 | RS0 | no connection | |
8 | LOS | Loss of Signal indication. Logic 0 indicates normal operation. | 5 |
9 | RS1 | Internally connect to circuit ground | |
10 |
V EER |
Receiver Ground (Common with Transmitter Ground) | 1 |
11 |
V EER |
Receiver Ground (Common with Transmitter Ground) | 1 |
12 | RD- | Receiver Inverted DATA out. AC Coupled | |
13 | RD+ | Receiver Non-inverted DATA out. AC Coupled |
14 |
V EER |
Receiver Ground (Common with Transmitter Ground) | 1 |
15 |
V CCR |
Receiver Power Supply | |
16 |
V CCT |
Transmitter Power Supply | |
17 |
V EET |
Transmitter Ground (Common with Receiver Ground) | 1 |
18 | TD+ | Transmitter Non-Inverted DATA in. AC Coupled. | |
19 | TD- | Transmitter Inverted DATA in. AC Coupled. | |
20 |
V EET |
Transmitter Ground (Common with Receiver Ground) | 1 |
FAULT
the TX output power or the laser temperature exceeding the preset alarm thresholds. A low output indicates normal operation. In the low state, the output is pulled to <0.8V.
DIS DIS
E-LINK’s LNK-SFP-10G-L45 serial transceivers support the 2-wire serial communication protocol as defined in the SFP+MSA. The standard SFP serial ID provides access to identification information that describes the transceiver’s capabilities, standard interfaces, manufacturer, and other information.
Additionally, E-LINK SFP+ transceivers provide a unique enhanced digital diagnostic monitoring interface, which allows real-time access to device operating parameters such as transceiver temperature, laser bias current, transmitted optical power, received optical power and transceiver supply voltage. It also defines a sophisticated system of alarm and warning flags, which alerts end-users when particular operating parameters are outside of a factory set normal range.
The SFP MSA defines a 256-byte memory map in EEPROM that is accessible over a 2-wire serial interface at the 8 bit address 1010000X (A0h).The digital diagnostic monitoring interface makes use of the 8 bit address 1010001X (A2h), so the originally defined serial ID memory map remains unchanged.
The operating and diagnostics information is monitored and reported by a Digital Diagnostics Transceiver Controller (DDTC) inside the transceiver, which is accessed through a 2-wire serial interface. When the serial protocol is activated, the serial clock signal (SCL, Mod Def 1) is generated by the host. The positive edge clocks data into the SFP transceiver into those segments of the E2PROM that are not write-protected. The negative edge clocks data from the SFP transceiver. The serial data signal (SDA, Mod Def 2) is bi-directional for serial data transfer. The host uses SDA in conjunction with SCL to mark the start and end of serial protocol activation. The memories are organized as a series of 8-bit data words that can be addressed individually or sequentially.
Người liên hệ: Mr. Michael Guo
Tel: 19928768315
Fax: 86-755-8312-8674
E-Link Gigabit Power Over Ethernet In phun 12 ~ 48VDC Đầu vào DIN Rail / Wall Mount
Cổng đơn 60W Cấp nguồn qua các thiết bị Ethernet Hỗ trợ Cài đặt Din Rail / Wall Mount
10/100 / 1000Mbps Công suất cao Poe In phun 95 watt 802.3bt Truyền 100m
48 Volt 2 Port Cisco POE Power Over Ethernet Injector 10 / 100 / 1000Mbps 15.4W
Bộ mở rộng quang Mini 4K HDMI Đầu vào USB đa chế độ không nén 300M
Bộ mở rộng sợi HDMI 4K SFP LC 80km Bộ mở rộng sợi quang đơn mode 10,3Gbps
SFP 5VDC HDMI qua Bộ mở rộng cáp quang Cổng Micro 4K USB 80Km
Bộ mở rộng cáp quang HDMI 4K * 2K HDCP 10,3Gbps SFP LC với âm thanh bên ngoài
Mini 3G / HD-SDI to Fibre Converter Extender với chức năng Tally hoặc RS485 Data
Bộ mở rộng video 3G-SDI SDI sang bộ chuyển đổi sợi quang qua đường truyền dài 20KM sợi quang
HD SDI To Fiber Optic Converter with Forward Audio
Ethernet over Fiber Converter SD/HD/3G-SDI + RS485/RS422/RS232 Data + 10/100M